| Last Modified: 11-29-2007 | 1.6 C | |
| Service Category: Vehicle Exterior | Section: Sliding Roof/Convertible | |
| Model Year: 2008 | Model: Sequoia | Doc ID: RM0000029GI015X |
| Title: SLIDING ROOF / CONVERTIBLE: SLIDING ROOF SYSTEM: DESCRIPTION (2008 Sequoia) | ||
|
DTC |
B2343 |
Position Initialization Incomplete |
DESCRIPTION
This DTC is stored when the sliding roof drive gear (sliding roof ECU) has not been initialized.
|
DTC Code |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
B2343 |
Sliding roof drive gear (sliding roof ECU) has not been initialized |
Sliding roof drive gear (Sliding roof ECU) |
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
|
1. |
INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) |
(a) Check that the sliding roof drive gear can be initialized
.
OK:
Sliding roof drive gear can be initialized.
|
|
2. |
CHECK DTC |
(a) Clear the DTCs
.
(b) Check for DTCs
.
Result
|
Result |
Proceed to |
|---|---|
|
No DTC is output |
A |
|
DTC B2343 is output |
B |
|
|
3. |
CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX - SLIDING ROOF ECU AND BODY GROUND) |
|
(a) Disconnect the U3 ECU connector. |
(b) Disconnect the U7 roof console box connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
U7-3 (CLS) - U3-7 (CLS) |
Always |
Below 1 Ω |
|
U7-3 (CLS) - Body ground |
Always |
10 kΩ or higher |
|
U7-4 (OPN) - U3-6 (OPN) |
Always |
Below 1 Ω |
|
U7-4 (OPN) - Body ground |
Always |
10 kΩ or higher |
|
U7-5 (DOWN) - U3-2 (DWN) |
Always |
Below 1 Ω |
|
U7-5 (DOWN) - Body ground |
Always |
10 kΩ or higher |
|
U7-6 (UP) - U3-1 (UP) |
Always |
Below 1 Ω |
|
U7-6 (UP) - Body ground |
Always |
10 kΩ or higher |
|
U7-7 (E) - Body ground |
Always |
Below 1 Ω |
|
|
4. |
INSPECT SLIDING ROOF SWITCH |
|
(a) Remove the sliding roof switch
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
1 (UP) - 5 (E) |
TILT switch is pressed to up |
Below 1 Ω |
|
TILT switch is not pressed to up |
10 kΩ or higher |
|
|
2 (DWN) - 5 (E) |
TILT switch is pressed to down |
Below 1 Ω |
|
TILT switch is not pressed to down |
10 kΩ or higher |
|
|
3 (CLS) - 5 (E) |
SLIDE switch is pressed to close |
Below 1 Ω |
|
SLIDE switch is not pressed to close |
10 kΩ or higher |
|
|
4 (OPN) - 5 (E) |
SLIDE switch is pressed to open |
Below 1 Ω |
|
SLIDE switch is not pressed to open |
10 kΩ or higher |
|
|
5. |
INSPECT ROOF CONSOLE BOX ASSEMBLY |
|
(a) Remove the roof console box with sliding roof switch
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
3 (CLS) - 7 (E) |
SLIDE switch is pressed to close |
Below 1 Ω |
|
SLIDE switch is not pressed to close |
10 kΩ or higher |
|
|
4 (OPN) - 7 (E) |
SLIDE switch is pressed to open |
Below 1 Ω |
|
SLIDE switch is not pressed to open |
10 kΩ or higher |
|
|
5 (DOWN) - 7 (E) |
TILT switch is pressed to down |
Below 1 Ω |
|
TILT switch is not pressed to down |
10 kΩ or higher |
|
|
6 (UP) - 7 (E) |
TILT switch is pressed to up |
Below 1 Ω |
|
TILT switch is not pressed to up |
10 kΩ or higher |
|
|
|